Audio Compressor
Turn down the loud parts so the quiet parts can be heard.
Free · runs in your browser · nothing is uploaded

How to use the audio compressor
- Press Choose audio file, or drop a file onto the page, and wait for the waveform.
- Optionally select a part. The saved file then holds only that part; with no selection it holds the whole file.
- Set Threshold, from -60 to 0 dB (default -24 dB).
- Set Ratio, from 1.5:1 to 20:1 (default 4:1).
- Set Attack, from 1 to 100 ms (default 10), and Release, from 20 to 1000 ms (default 150).
- Leave “Make up the lost level automatically” ticked to keep the overall level, or untick it to let the result come out quieter.
- Choose a format in the Save panel and press the Save button. The sample rate and channels default to the source.
- Read the largest gain reduction in the result panel, listen in the small player, and press Download.
Start with the defaults, then lower the threshold or raise the ratio in small steps and compare the saved results by ear. Press Play before saving to hear the unprocessed selection. The line above the Save button shows the expected length and size.
Tick and untick “Make up the lost level automatically” and save twice if you want to compare the two results by ear. The result panel reports the largest gain reduction, so a value of only 1 or 2 dB means the settings barely touched the file, while a large value means the threshold is low or the ratio high. Change one control at a time between saves.
What is audio compression?
Audio compression reduces the dynamic range of a sound, the gap between its quietest and loudest parts. The loudest moments are turned down while quiet ones stay where they are, so the recording sits in a narrower band of volume. This helps when a voice jumps in and out of a mix or an instrument has sharp peaks.
A level detector watches the signal across both channels together, so the stereo image does not shift. Once the level passes the threshold, the part above it is reduced according to the ratio.
How do threshold and ratio work together?
The threshold says where compression starts, and the ratio says how firmly the excess is pulled back. At 2:1 half of the excess survives, at 4:1 a quarter survives, and at 20:1 the level is held almost at the threshold, which behaves like a limiter. Signals below the threshold are untouched.
A lower threshold means more of the file is compressed, and a higher ratio means each loud passage is reduced by more.
How do attack and release change the sound?
Attack is how quickly the compressor reacts to a loud sound, and release is how quickly it lets go afterwards. A fast attack catches short peaks but can dull the start of a sound. A slow release sounds more natural, but it may let the next loud sound through before the gain recovers.
What does automatic make-up gain do?
It adds back the reduction that a full-scale signal would receive, so the compressed file is not quieter overall than the original. The option is ticked by default and the make-up amount is worked out for you. If the result then clips, untick the option and raise the level afterwards with the MP3 Volume Booster or Normalize Audio pages.
How does the threshold and ratio change the level?
Above the threshold the level is divided by the ratio. With a threshold of -24 dB and a ratio of 4:1, a signal at -12 dB is 12 dB over the threshold, so it comes out 3 dB over, at -21 dB: a reduction of 9 dB. Signals below the threshold are untouched. The table is worked out for those settings.
| Input level | Output level | Gain reduction |
|---|---|---|
| -40 dB | -40 dB | 0 dB |
| -30 dB | -30 dB | 0 dB |
| -24 dB | -24 dB | 0 dB |
| -18 dB | -22.5 dB | 4.5 dB |
| -12 dB | -21 dB | 9 dB |
| -6 dB | -19.5 dB | 13.5 dB |
| 0 dB | -18 dB | 18 dB |
Frequently asked questions
What is audio compression?
Here it means dynamic range compression: the loud parts are lowered so the recording is more even. The file size does not change much, because the saved format decides that.
How do I compress an MP3 to a smaller size?
Use the Compress Audio File page. This page evens out loudness, and it saves the result as a re-encoded MP3, WAV, OGG, FLAC or M4A.
Which preset should I pick?
There are no presets, only the controls. The defaults of -24 dB, 4:1, 10 ms and 150 ms suit a first pass, and the gain reduction figure in the result tells you how much was done.
Will compression make my audio louder?
Not by itself, since it lowers peaks. With automatic make-up on, the average level is brought back up, so the result is not quieter overall.
Does it work on mobile?
Yes, in a phone browser, within 150 MB per file and about 15 minutes of decoded stereo audio. A computer allows 600 MB and about 60 minutes.
Is it free, and is my file uploaded?
It is free, with no account. The file is processed in your browser and never leaves your device.
Which formats can I open and save?
MP3, WAV, OGG, M4A, AAC, FLAC, AIFF and Opus open. The result saves as MP3, WAV, OGG Vorbis, FLAC or M4A, and M4A appears only in browsers that can encode AAC, such as Chrome, Edge and Safari 26 or later.
Can I compress only part of a file?
Yes. Select it on the waveform and save. The saved file then contains just that part.
Related tools
- Compress Audio File: use it to make the file smaller.
- Normalize Audio: use it to set the overall level to a target.
- MP3 Volume Booster: use it to raise the level by a fixed number of dB.
- Fade Out Audio: use it to end a clip with a gradual drop in volume.
- Silence Remover: use it to remove quiet gaps from a recording.
- Audio Trimmer: use it to keep only the part you need.
- Audio Mixer: use it to balance several tracks against each other.
- Free Audio Editor: use it for several edits in one place.