Audio Mixer
Layer a voice over music, or any tracks over each other, and save the mix.
Free · runs in your browser · nothing is uploaded

How to mix audio files online
- Press Choose audio files and select two or more files, or drop them onto the page. Add more later with Add more files.
- Check the list. Each row shows the name, length, sample rate and channels. The first row is the base track. Move a file with the arrows or remove it with ×.
- In the Gain (dB) box of each track, type 0 to leave it unchanged, a negative number to make it quieter, or a positive number to make it louder.
- In the Start at (s) box, type how many seconds to wait before that track begins. Leave 0 to start it with the base.
- Choose a format in the Save panel, and change the sample rate or channels if you need to.
- Press the Save button and watch the progress bar. Cancel stops it.
- Listen in the small player, edit the file name if you like, and press Download.
There is no timeline to drag clips on, and no waveform. Trim each file first if only part of it should be used, and keep every file at the same sample rate, because a mismatch stops the page with a message.
Gain and Start at (s) accept any number you type, including decimals such as -7.5 or 0.25. The first row is the base, so add the longest or most important track first. If the saved mix is too quiet or too loud overall, change the gains and save again; the original files are never altered.
How do I put music under a voice?
Add the voice first so it is the base, then lower the music track with a negative gain. A cut of around 10 dB is a common starting point, which leaves the speech clear and the music audible. Use Start at (s) to delay the music if the voice should speak first.
Save the mix, listen to it in the player, and adjust the gain by a few dB if the balance is wrong. A soft or distant voice may need the music lowered further. Keep the music loop long enough to cover the voice, or repeat it first with the Loop Audio page.
How does the mixer avoid clipping?
The tracks are added sample by sample. If the sum goes above full scale, the whole mix is lowered by exactly the amount needed to avoid clipping, and a note on the result tells you so. Every track keeps its balance with the others, because they are all turned down together.
Because positive gains push the total towards full scale, it is usually better to lower the loud tracks than to raise the quiet ones. If the whole mix comes out quieter than you want, the Normalize Audio page can raise it afterwards.
How long is the mix?
It is as long as the track that ends last, counting any delay you set. A track of 30 seconds with Start at (s) set to 20 ends at 50 seconds, so the mix is at least 50 seconds long. Shorter tracks end earlier and leave the rest of the mix to the others.
What is the difference between mixing and joining?
Joining puts files one after another, while mixing plays them together. Use the Audio Joiner when the clips should follow each other. A mono track mixed with stereo is copied to both channels, so it sounds the same in each speaker.
How do dB values change the volume of a track?
Each 6 dB doubles or halves the amplitude, and each 20 dB changes it by a factor of 10. A track set to -6 dB plays at about half its original level, and -20 dB at one tenth. The table lists the multipliers; if the combined mix would clip, the tool lowers all of it together.
| Gain | Multiplier |
|---|---|
| +6 dB | 1.995 |
| +3 dB | 1.413 |
| 0 dB | 1.000 |
| -3 dB | 0.708 |
| -6 dB | 0.501 |
| -10 dB | 0.316 |
| -12 dB | 0.251 |
| -20 dB | 0.100 |
Frequently asked questions
How can I mix audio together online?
Add two or more files, set the gain and start time for each track, and save the mix. The work happens in your browser, so the files stay on your device, and the tool needs no account.
How do I mix two audio files together?
Add both files, set each one’s Gain (dB) and Start at (s) values, and press the Save button. One file comes out with both playing at once.
Can I set each track’s volume?
Yes, with the Gain (dB) box on its row. A value of 0 leaves the track as recorded, and negative values make it quieter.
How loud will the mix be?
As loud as the tracks add up to. If the total would pass full scale, the whole mix is lowered just enough to avoid clipping, and the page says so.
How many tracks can I use?
The page sets no fixed number. The decoded audio of all files is held in memory at once, so a long list of long files can run out of memory.
What format is the mix?
Pick MP3, WAV, OGG, FLAC or M4A in the Save panel. M4A appears only in browsers that can encode AAC, such as Chrome, Edge and Safari 26 or later. MP3 is written at a constant 128 to 320 kbps.
Can I add video, mute or solo tracks, or save a project?
No. This is a layering tool for audio files only: no timeline, no solo or mute buttons, no video and no project files. Remove a track from the list if you do not want it in the mix.
What are the size limits?
Each file can be 600 MB on a computer and 150 MB on a phone. Decoded stereo at 44.1 kHz takes about 212 MB for 10 minutes.
Related tools
- Audio Joiner: use it to place files one after another.
- MP3 Joiner: use it to join MP3 files without re-encoding.
- Loop Audio: use it to repeat a short music bed so it lasts the whole mix.
- Audio Trimmer: use it to keep only the part of a file you need.
- Normalize Audio: use it to raise the level of a finished mix.
- Audio Compressor: use it to even out a loud and quiet voice before mixing.
- Fade Out Audio: use it to end the mix with a fade.
- Free Audio Editor: use it for several edits in one place.