Trim, cut and convert audio in your browser

Cut Audio

Select the part you want gone; the sound before and after it is joined into one file.

Free · runs in your browser · nothing is uploaded

Open on Tone Snip

This embed was switched off for this website. Open on Tone Snip

Want this audio tool on your own site? The embed code is on the about page. Embed code

To cut audio, select the section you want gone, delete it, and let the sound before and after join up so no gap is left. This page does exactly that for MP3, WAV, OGG, M4A, AAC, FLAC, AIFF and Opus files. Typical jobs are removing a cough, a long pause, an ad break or a mistake from a recording. A short crossfade, 0.02 s by default, smooths the join, and you can listen to the selection, with Play or Loop, before you save. Cutting here means deleting the selection. To keep the selection and discard everything else, use the Audio Trimmer.
Cut audio example

How to cut a section out of audio

  1. Press Choose audio file, or drop a file onto the page, and wait for the waveform.
  2. Zoom in with the plus button, the mouse wheel or a two-finger pinch until the section is easy to see. The scroll bar moves along a zoomed view.
  3. Drag across the waveform over the part to remove, then drag either handle to adjust the edges.
  4. For exact timing, type the start, end or length as minutes:seconds.milliseconds in the three boxes under the waveform. Start here and End here use the playhead position.
  5. Press Play, or tick Loop, to hear what will be deleted.
  6. Set the Crossfade, from 0 to 1 second.
  7. Choose a format in the Save panel and press the Save button. The line above it shows the expected length and size.
  8. Check the result in the small player, edit the file name if needed, and press Download.

Left and Right move the playhead by 0.1 s (1 s with Shift) while the waveform is focused, [ and ] set the start and end at the playhead, and Escape clears the selection. The Save button stays disabled until a section is selected.

The page starts with a section already selected, so check the handles before you save, because the Save button cuts exactly what is shaded. A crossfade of 0 gives a hard join, which is fine when both edges sit in silence. Use Edit the result after saving to cut another section from the new file.

What is the difference between cutting and trimming audio?

Cutting deletes the selection and keeps the rest. Trimming does the opposite: it keeps the selection and removes everything outside it. Both work from a start and an end point on the waveform, so the choice depends on whether the part you marked is the part you want to lose or the part you want to keep.

What does the crossfade do at the cut?

The crossfade blends the end of the sound before the cut into the start of the sound after it, using an equal-power curve. A value of 0 joins the two sides with no blend, which can leave a click if the waveform is not at a quiet point. Larger values smooth the join but shorten the file by that amount.

When the selection touches the very start or the very end of the file there is no sound on one side, so no blend is made.

Can I make several cuts in one file?

Yes, one after another. After saving, press Edit the result to load the cut file as the new source, then select the next section. For a quicker run of edits use the Free Audio Editor, which has Undo and Redo for the last four steps.

Which formats can the result be saved in?

The result can be saved as MP3, WAV, OGG Vorbis, FLAC or M4A; the MP3 here is re-encoded at a constant bitrate. To cut an MP3 without re-encoding it, use the MP3 Cutter linked below, which keeps one selection.

FormatOptions
WAV16-bit, 24-bit or 32-bit float
OGG Vorbisfour quality presets
FLAC16-bit or 24-bit
M4A (AAC)64 to 256 kbps, in browsers that can encode AAC

The Save panel can also change the sample rate and switch between mono and stereo; by default both stay as in the source.

How long is the file after a cut?

The result is the original length minus the selection, minus the crossfade when there is a part on both sides of the cut. Cutting 10 seconds out of a 60-second file with no crossfade leaves 50 seconds; a 0.5-second crossfade leaves 49.5 seconds. The table shows how the crossfade changes the length.

CrossfadeOriginalSelection removedResult
0 s60 s10 s50 s
0.02 s60 s10 s49.98 s
0.1 s60 s10 s49.9 s
0.5 s60 s10 s49.5 s
1 s60 s10 s49 s

Frequently asked questions

What is the difference between cut and trim audio?

Cut deletes the selection and joins the rest. Trim keeps the selection and deletes the rest. This page cuts, and the Audio Trimmer trims.

How do I cut an MP3 file online?

Open the MP3, select the section to delete, and save. The result can be an MP3 again, or WAV, OGG, FLAC or M4A, but this page always re-encodes the sound. The MP3 Cutter keeps a selection as a lossless MP3.

Can I edit a podcast with this tool?

You can take out coughs, pauses, mistakes or an ad break. It does not remove background noise or add music, so it covers cutting rather than full production.

Which audio formats does it support?

It opens MP3, WAV, OGG, M4A, AAC, FLAC, AIFF and Opus files. DSF is not among them, so convert it to WAV or FLAC first. If your browser cannot play a file, an error says so.

Is there a limit on the file size, and does it work on a phone?

The limit is 600 MB per file on a computer and 150 MB on a phone. Decoded audio must fit in memory: about 60 minutes of 44.1 kHz stereo on a computer and about 15 minutes on a phone.

Is it safe for private recordings?

The file is read and edited inside your browser, and your input is not uploaded to a server. Tags and cover art from the source are not copied into the result.

How do I merge two MP3 files or add music?

Cutting removes sound from one file. To put files one after another, use the MP3 Joiner or Audio Joiner. To layer one sound over another, use the Audio Mixer.

What if the cut starts at the very beginning?

Nothing is blended there, so the crossfade is skipped and the result is the original length minus the selection.