Trim, cut and convert audio in your browser

MP3 to M4R

Turn an MP3 into an M4R ringtone: select the part and save.

Free · runs in your browser · nothing is uploaded

Open on Tone Snip

This embed was switched off for this website. Open on Tone Snip

Want this audio tool on your own site? The embed code is on the about page. Embed code

M4R is the file type iPhone ringtones use, and converting an MP3 to M4R means re-encoding a short part of the song as AAC and giving it the .m4r extension. The page decodes the MP3 in your browser and encodes the section you select at 64 to 256 kbps (128 kbps is preselected), with an optional fade in and fade out of 0 to 5 seconds. Because Apple’s help gives 30 seconds as the longest iPhone ringtone, the tool asks for a selection rather than converting the whole song, and it warns when the selection is longer. Any M4R converter works the same way here: MP3, M4A, WAV, OGG, FLAC and AIFF files all open.
Mp3 to m4r example

Making an M4R from an MP3

  1. Press Choose audio file and select the MP3, or drop it onto the page.
  2. A starting selection of up to 20 seconds appears on the waveform. Drag it or its handles to the part you want, or type Start, End and Length values.
  3. Press Play to preview, and Loop to hear it repeat. The Stop button returns to the start of the selection.
  4. Watch the note under the controls; it becomes a warning if the selection is longer than 30 seconds.
  5. Set Fade in and Fade out (0.3 s and 1 s at first).
  6. In Save, choose a Bitrate between 64 and 256 kbps.
  7. Press Save as M4R. A progress bar appears, and Cancel stops it.
  8. When “Ready.” shows, press Download. The file ends in .m4r.

Tip: use the zoom buttons or the mouse wheel to place the edges precisely. You can rename the result in the File name box before saving. M4R needs a browser that can encode AAC, which Chrome, Edge and Safari 26 or later can. If yours cannot, the page says so. The Save button also stays off until a selection exists.

Check the length at Length before saving: a ringtone that runs over 30 seconds gets the warning described above, and trimming a few seconds off is easier now than after you have transferred the file.

How do you convert to M4R?

Decode, cut and re-encode. The page decodes the MP3, applies your fades, encodes the chosen part as AAC and writes the result with the .m4r extension. M4R is not a different codec from M4A: it is AAC audio in an MP4 container, labelled for ringtones. The steps above are the whole job; no software is installed.

Will going from MP3 to M4R reduce my audio quality?

Yes, a little, and it cannot be avoided. The MP3 is already lossy, and re-encoding the selection as AAC is a second round of lossy compression. The quality is that of AAC at the bitrate you choose, taken from a source that has lost detail already. A higher bitrate keeps more of the MP3’s sound, and the original MP3 is left untouched.

Which is better, M4R or MP3?

They are for different jobs. M4R is the iPhone ringtone file type, whereas MP3 is a general listening format. This page does not save MP3 for an iPhone ringtone. Apple’s own help describes GarageBand on the iPhone as the way to make a custom ringtone (Share, then Ringtone, up to 30 seconds), and Settings > Sounds & Haptics > Ringtone for choosing it. It does not describe copying an .m4r file from a computer, although many people do that with Finder, Apple Devices or iTunes.

What bitrate will the M4R use?

The one you choose under Bitrate: 64, 96, 128, 192 or 256 kbps, with 128 kbps selected at first. The bitrate sets the size, and the line above the Save button shows it before you commit. Because a ringtone is short, even the highest setting gives a small file; the size table below lists the numbers.

Will the M4R keep the sample rate of the MP3?

Yes, unless you change it. The sample rate and mono or stereo layout carry over from the MP3 by default. Tags and cover art are not copied into the M4R.

How big is a ringtone file?

A ringtone is short, so the file is small. At 128 kbps AAC a 30-second ringtone, the longest that the Apple help pages allow for an iPhone, is about 0.46 MB and a 15-second one about 0.23 MB. The table gives sizes for other lengths and bitrates (1 MB = 1,048,576 bytes).

Length64 kbps128 kbps256 kbps
15 s0.11 MB0.23 MB0.46 MB
20 s0.15 MB0.31 MB0.61 MB
30 s0.23 MB0.46 MB0.92 MB

Frequently asked questions

Why is the M4R louder or quieter than the MP3?

The page changes no volume; it only applies the fades you set. If the ringtone sounds different, the cause is the phone’s volume or the part of the song you picked.

How do I turn an MP3 into a ringtone?

Select up to 30 seconds of the song here, save it as M4R, and add it to the iPhone. Apple documents GarageBand for that last step.

What is an M4R file?

M4R is the Apple iPhone ringtone file type: AAC audio in an MP4 container with the .m4r extension.

How do I change MP3 to M4R on a Mac?

Open the page in a desktop browser with an AAC encoder, such as Chrome, Edge or Safari 26 or later, and follow the steps above. Nothing is installed.

Is my MP3 private during conversion?

Yes. The file is decoded and encoded on your own device and is not sent to a server.

Can I batch convert hundreds of MP3 files to M4R?

No. The page handles one file and one selection at a time.

How long does converting a 1-hour MP3 to M4R take?

A ringtone is capped near 30 seconds, so only the selection is encoded. A long MP3 must also fit in memory: about 60 minutes of 44.1 kHz stereo on a computer.

How do I open an M4R or MP3 file?

Most players open MP3. An M4R is made to be used as an iPhone ringtone.