Trim, cut and convert audio in your browser

MP3 Volume Booster

Pick how many dB louder or quieter, check the peak warning, and save.

Free · runs in your browser · nothing is uploaded

Open on Tone Snip

This embed was switched off for this website. Open on Tone Snip

Want this audio tool on your own site? The embed code is on the about page. Embed code

This MP3 volume booster makes a file louder: open it, set a volume change in decibels, and save a copy with that gain applied. The range runs from -30 to +30 dB with +6 dB as the starting value, and playback uses the same gain, so you hear the change before you save. A line under the controls shows how loud the loudest peak will be, or warns when the boost would clip. Increasing the volume of an audio file, an audio volume booster and changing audio volume are all the same operation here. The page also opens WAV, OGG, M4A, AAC, FLAC, AIFF and Opus files.
Mp3 volume booster example

How to boost the volume of an MP3

  1. Press Choose audio file and pick your MP3, or drop it onto the page. The page reads the file once to find its loudest peak.
  2. Optionally drag across the waveform to change only a part. The saved file then holds just that part; with no selection it holds the whole file.
  3. Set Volume change, from -30 to +30 dB. The default is +6 dB.
  4. Press Play. The preview uses the same gain, so you can judge the result by ear.
  5. Read the line under the controls: “The loudest peak will be -2.1 dB” is fine, “would reach +x dB and clip” is not.
  6. Leave “Stop at full scale (hard limit)” ticked unless you want peaks to run past full scale.
  7. Choose MP3, WAV, OGG, FLAC or M4A in the Save panel and press the Save button.
  8. Check the result in the small player, edit the file name if you like, and press Download.

If the peak line warns about clipping, lower the Volume change until it reads below 0 dB. Use Select all or Clear selection under the waveform to go back to the whole file, and the line above the Save button shows the expected length and size of the result.

How do I make an MP3 louder without distortion?

Raise the volume change until the peak line under the controls shows a value just below 0 dB. Distortion starts when a peak is pushed above full scale and cut off, which sounds harsh. A file that already peaks close to 0 dB has no room for a boost, while a quiet voice recording usually has plenty.

The tool reads the whole file once so that this warning is exact. With the hard limit ticked, peaks that would pass full scale are cut off at it instead of wrapping around.

What is the difference between boosting and normalizing?

Boosting adds the number of decibels you choose, whatever the file’s current level. Normalizing measures the file and works out the gain that reaches a target. Use the booster when you know how much more volume you want, and the Normalize Audio page when you want the tool to find the gain.

Both multiply every sample by one constant, so neither changes the balance between loud and quiet parts. To even those out, use the Audio Compressor.

Can the boosted file stay an MP3?

Yes, but it is encoded again: the louder sound cannot be made by copying the old MP3 frames. Choose MP3 (constant bitrate, 128 to 320 kbps) to keep the format, which adds a second round of lossy compression. WAV and FLAC keep the boosted sound exactly, while OGG and M4A give a smaller lossy file.

Why does a boosted recording sound noisier?

A boost changes the level, not the shape of the sound. Background hiss and room noise are raised by exactly the same amount as the voice or music. If a recording is quiet because the microphone was far away, a large boost will lift that noise as well.

How much louder is +6 dB?

Plus 6 dB doubles the amplitude, which most people hear as clearly louder but not twice as loud. A boost is limited by the loudest peak: a file that already peaks at -3 dB can only be raised by 3 dB before it reaches full scale and clips. The table converts dB to a multiplier.

ChangeAmplitude multiplierFile peaking at -3 dB would peak at
+3 dB1.410 dB
+6 dB2.00+3 dB (clips)
+10 dB3.16+7 dB (clips)
+20 dB10.00+17 dB (clips)
-6 dB0.50-9 dB

Frequently asked questions

How do I make an MP3 louder?

Open the file, set Volume change to the number of dB you want, check that the peak line stays below 0 dB, and save. Use the same steps to increase the volume of any supported audio file online.

Will the audio clip if I boost too much?

Yes. A boost that pushes a peak above full scale is cut off, which sounds harsh. The peak line warns you before you save, and the hard limit option decides whether peaks are held at full scale.

What is the difference between boosting and normalizing?

Boosting applies a fixed gain you choose. Normalizing finds the gain that brings the file to a target level. Both multiply the whole file by one number.

Which formats does it support?

MP3, WAV, OGG, M4A, AAC, FLAC, AIFF and Opus files open. The result saves as MP3, WAV, OGG, FLAC or M4A, with M4A only in browsers that can encode AAC, such as Chrome, Edge and Safari 26 or later.

Does it work on mobile?

Yes, in a phone browser, within 150 MB per file and about 15 minutes of decoded stereo audio.

Is it free, and is the file uploaded?

It is free, needs no software and no account. The audio is processed in your browser and never leaves your device.

How many dB should I add?

It depends on the file. Add as many as the peak line allows while it stays below 0 dB. A typical quiet voice recording can take far more than a mastered music track, which often peaks close to 0 dB already.

Can I make audio quieter?

Yes. Set Volume change to a negative value, down to -30 dB.