Trim, cut and convert audio in your browser

Silence Remover

Find the pauses in a recording and cut them out, or just trim the quiet start and end.

Free · runs in your browser · nothing is uploaded

Open on Tone Snip

This embed was switched off for this website. Open on Tone Snip

Want this audio tool on your own site? The embed code is on the about page. Embed code

A silence remover first locates every quiet stretch, then deletes the long ones, trims only the two ends, or shrinks each long pause, depending on the mode. This one measures the sound in 10 millisecond blocks and treats a block as silent when it falls below a threshold that you control. The silent parts are shaded on the waveform before you save, with a count and a total in seconds, and the result panel then reports how many seconds were removed and in how many places. It opens MP3, WAV, OGG, M4A, AAC, FLAC, AIFF and Opus files, and works on a selection if you make one.
Silence remover example

How to remove silence from audio

  1. Press Choose audio file, or drop a file onto the page, and wait for the waveform.
  2. Optionally drag across the waveform to limit the job to one part. With no selection the whole file is used.
  3. Under Mode, pick “Remove all long silences”, “Trim only the start and end” or “Shorten long silences”.
  4. Set the Silence threshold, from -80 to -20 dB (default -50 dB).
  5. Set the Shortest silence to act on, from 0.1 to 5 seconds (default 0.4 s).
  6. Set Keep around sound, from 0 to 1 second (default 0.1 s).
  7. Look at the shaded parts and the line beneath the waveform, which says how many silent parts were found and how long they add up to. It updates whenever a control changes.
  8. Choose a format in the Save panel and press the Save button. A progress bar runs, and Cancel stops it.
  9. Listen to the result in the small player, edit the file name if you like, and press Download.

If the count looks wrong, move the threshold a few dB before changing anything else. Playing the file with Play also helps to judge whether a shaded gap is a real pause.

Move the selection handles to analyse only one section, such as the middle of an interview. If the shading covers too much, lower the threshold toward -60 dB; if it misses obvious pauses, raise it toward -35 dB. The result panel afterwards says how many seconds were removed and in how many places.

What is the difference between the three modes?

“Remove all long silences” deletes every silent stretch longer than the minimum, leaving the Keep around sound padding next to the sound. “Trim only the start and end” removes silence from the beginning and end of the selection and leaves pauses in the middle. “Shorten long silences” shrinks each long pause down to the keep length instead of deleting it.

Shortening is the gentler choice for speech, because the pauses stay audible. Removing everything can make a voice sound rushed.

How does the silence threshold decide what counts as silence?

The threshold is the level below which a 10 ms block counts as silent; the louder channel decides in a stereo file. A lower value, such as -60 dB, catches only very quiet passages. A higher one, such as -35 dB, also removes room noise and soft breaths.

A recording with constant background hiss may need a higher threshold than a clean one, because the hiss never drops below a low setting. Watch the shaded parts while you adjust it.

What does Keep around sound do?

It sets how much quiet is left beside the sound, from 0 to 1 second (default 0.1 s). In the remove and trim modes it is the padding kept next to the sound, so words do not start or stop abruptly. In the shorten mode it is the length each long pause is reduced to.

Will the edits click?

A 5 ms fade is applied at every join, so the joins do not click. Pauses shorter than the Shortest silence to act on setting are left alone, which keeps the gaps between words and the natural rhythm of speech.

The source sample rate is kept, and a mono file stays mono unless you change the channels in the Save panel.

How much silence does each mode remove?

Each mode shortens the built-in 9-second demo clip differently. That clip has four notes with pauses between them, a 0.4 s pause before the first note and a 0.5 s pause after the last. With the threshold at -50 dB and the shortest silence at 0.4 s, “Remove all long silences” leaves 6 s, “Trim only the start and end” leaves 8.3 s and “Shorten long silences” leaves 6.7 s.

ModeKeep around soundDemo clip becomes
Original-9 s
Remove all long silences0.1 s6 s
Trim only the start and end0.1 s8.3 s
Shorten long silences0.3 s6.7 s

The “Try a sample” button on this page loads the same clip, so these numbers can be reproduced.

Frequently asked questions

What is a silence remover?

It is a tool that detects quiet stretches in a recording and removes or shortens them. Podcasts, lectures, interviews and voice memos are the usual inputs.

How do I remove silence from a podcast or voice recording?

Open the file, choose “Remove all long silences” or “Shorten long silences”, check the shaded parts on the waveform, and save. Raise the threshold if breaths and room noise are not caught.

Can I adjust the silence threshold?

Yes. Silence threshold runs from -80 to -20 dB, and the Shortest silence to act on from 0.1 to 5 seconds. Both update the shading straight away.

Will it cut off my speech?

Keep around sound leaves a small padding next to every sound, 0.1 s by default and up to 1 s. If words sound clipped, raise it or lower the threshold.

How do I avoid clicks or pops?

You do not need to do anything: a 5 ms fade is applied at every join.

My recording has background noise. Can it still find the pauses?

Yes, if you raise the threshold above the noise level, for example towards -35 dB. If the setting is too high, soft words may be treated as silence, so listen to the result.

Which files work, and is there a size limit?

MP3, WAV, OGG, M4A, AAC, FLAC, AIFF and Opus open, up to 600 MB on a computer and 150 MB on a phone. Decoded audio must fit in memory: about 60 minutes of 44.1 kHz stereo on a computer and 15 minutes on a phone.

Is it free, and is my audio sent anywhere?

It is free and needs no account. The audio is processed in your browser tab and is not sent to a server. Tags and cover art are not copied into the result.