Trim, cut and convert audio in your browser

WAV to FLAC

Open a WAV file and save it as FLAC.

Free · runs in your browser · nothing is uploaded

Open on Tone Snip

This embed was switched off for this website. Open on Tone Snip

Want this audio tool on your own site? The embed code is on the about page. Embed code

FLAC squeezes a WAV into a smaller file and gives back exactly the same samples when it is played, so the sound is untouched. This page encodes FLAC in your browser with libFLAC at compression level 5. You open the WAV, choose 16-bit or 24-bit, check the estimated size and save the .flac file. A new sample rate or a mono or stereo layout is optional, and a selection on the waveform encodes only that part. The saving varies with the music, but it usually lands at about half to two thirds of the WAV. Tags and cover art in the WAV are not copied. Use it for archives and for storage where disk space matters.
Wav to flac example

Compressing a WAV into FLAC

  1. Press Choose audio file and open the WAV, or drop it onto the page. The file line shows its length, sample rate, channels and size.
  2. For a partial encode, drag across the waveform or fill in Start, End and Length; Start here, End here, Select all and Clear selection adjust the range.
  3. In Save, open Bit depth and choose 16-bit or 24-bit. A 24-bit WAV needs 24-bit to stay exact.
  4. Leave Sample rate and Channels at “Same as source” so that the samples stay as recorded.
  5. Read the estimate above the button; the page assumes about 60 percent of the WAV size, and the real figure depends on the music.
  6. Press Save as FLAC. The progress bar runs in 20-second blocks, and Cancel stops it.
  7. When “Ready.” appears, check the result in the small player and press Download.

Tip: FLAC supports only 16 and 24 bits here. A 32-bit float WAV has to be saved at one of those, so it cannot be kept bit for bit; leave such files as WAV if exactness matters. You can also rename the result in the File name box before saving.

Use Edit the result if you want to trim the FLAC further, or press Change file to open the next WAV. Check the file line first if the source is an unusual WAV, because 8-bit and 64-bit float files are read as well.

What does FLAC do that WAV doesn’t?

It makes the file smaller without changing a single sample. FLAC stands for Free Lossless Audio Codec: it packs the audio the way a zip file packs documents, and decoding unpacks it perfectly. A WAV skips that step, so it is larger and simpler. The sound of the two is identical.

Does converting WAV to FLAC lose any quality?

No, provided you keep the same bit depth and sample rate. The encoder is lossless, so converting back to WAV returns the original samples. Only a lower bit depth, a new sample rate or a different channel layout would change the audio, and those options are off by default.

Which bit depth should I choose?

Match the WAV. Sixteen bits suits ordinary 16-bit recordings, and 24 bits suits studio material recorded at 24-bit. Choosing 24-bit for a 16-bit file does not add detail, and it makes the FLAC larger than needed.

When should I keep the WAV instead?

When the next program is an editor, sampler or device that accepts WAV but not FLAC. Because the FLAC rebuilds the WAV’s samples exactly, nothing is lost by archiving as FLAC and converting back later with the FLAC to WAV page. How much disk space you save depends on the music, and the size estimate near the Save button is only a rough figure until the file is written.

What happens to the WAV’s tags and settings?

Tags and cover art are not copied into the FLAC, so add them in a tag editor if your library needs them. The sample rate and channel layout carry over unless you change them, and the audio is encoded in 20-second blocks, which keeps memory use low for long recordings. The original WAV is never touched.

How big will the FLAC file be?

FLAC compresses without losing anything, so the size depends on the music: it is typically about half to two thirds of the WAV, and the table uses 60 percent as a rough figure. A 3-minute stereo song is about 18 MB as 16-bit FLAC (1 MB = 1,048,576 bytes).

LengthWAV 16-bitFLAC 16-bit (about 60% of WAV)FLAC 24-bit (about 60% of WAV)
1 min10.1 MB6.1 MB9.1 MB
3 min30.3 MB18.2 MB27.3 MB
5 min50.5 MB30.3 MB45.4 MB
10 min101 MB60.6 MB90.8 MB

Frequently asked questions

How do I convert WAV to FLAC?

Open the WAV here, pick 16-bit or 24-bit and press Save as FLAC. The progress bar shows the blocks as they are encoded, and Download appears when the file is ready.

What is a WAV file?

WAV is a file format that stores audio uncompressed as PCM samples.

What is a FLAC file?

A FLAC file stores audio with lossless compression, so it plays back identically to the source but is smaller.

How do I open a WAV file?

Any common media player or audio editor opens WAV. The page opens it too, drawing the waveform and playing the audio.

Can I encode a 24-bit WAV?

Yes. Choose 24-bit in the Bit depth list and the samples are kept exactly. A 16-bit WAV is best saved as 16-bit FLAC.

How do I open a FLAC file, and what if my player cannot?

Many current players and editors handle FLAC. If yours does not, turn the file back into a WAV with the FLAC to WAV page; nothing is lost on the way.

How big can the WAV be?

The page refuses a WAV over 600 MB on a computer or 150 MB on a phone, and the decoded sound must fit in memory too.