Trim, cut and convert audio in your browser

WAV to M4A

Open a WAV file and save it as M4A.

Free · runs in your browser · nothing is uploaded

Open on Tone Snip

This embed was switched off for this website. Open on Tone Snip

Want this audio tool on your own site? The embed code is on the about page. Embed code

An M4A made from a WAV is the sensible way to get AAC: the encoder starts from the uncompressed original, so only one lossy step happens. This page opens the WAV and encodes AAC-LC with the browser’s AudioEncoder at 64, 96, 128, 192 or 256 kbps, then saves a file that plays on iPhones, Android phones and computers. Chrome, Edge and Safari 26 or later include an AAC encoder; the page checks for one. A new sample rate or mono and stereo choice is optional, and a selection on the waveform encodes only that part. The M4A is far smaller than the WAV, with some detail gone for good, so keep the WAV. Tags and cover art are not copied.
Wav to m4a example

Encoding a WAV as M4A

  1. Press Choose audio file and open the WAV, or drop it on the page; the line below shows its name, length, sample rate, channels and size.
  2. To encode only a section, drag across the waveform and adjust the handles. Start, End and Length accept typed times, and Start here and End here use the playhead.
  3. In Save, open Bitrate and choose between 64, 96, 128, 192 and 256 kbps. The preselected 128 kbps is a reasonable first try.
  4. Pick another Sample rate or Channels value only when required; both begin as “Same as source”.
  5. Read the length and size shown above the button. Change the bitrate and read it again if the size is not right.
  6. Press Save as M4A, watch the progress bar and use Cancel if you need to stop.
  7. Press Download when “Ready.” appears.

Without an AAC encoder in your browser, the page shows a message that says to open it in Chrome, Edge or Safari 26 or later, or to use a converter to WAV, OGG or FLAC. You can also rename the result in the File name box, and a file over 600 MB (150 MB on a phone) will not open.

Listen to the result in the small player before downloading it. If it sounds thin, repeat the job at a higher bitrate; the WAV on your device is never changed.

What is inside an M4A, and how is it different from a WAV?

An M4A is an MP4 container that normally holds AAC audio, a lossy codec. A WAV holds uncompressed PCM samples. So the M4A keeps the sound recognizably but throws away detail the encoder judges least audible, and it needs a decoder to play, while a WAV does not. Almost every phone and computer has the M4A decoder.

Is the WAV to M4A converter free?

Yes. The encoding happens inside your browser, using the AAC encoder that Chrome, Edge and Safari 26 or later ship, so no server is involved and nothing is queued. If your browser has no AAC encoder, the Save button stays disabled and M4A is unavailable there; the WAV to OGG and WAV to FLAC converters still work.

How long does converting WAV to M4A take?

The time depends on the length of the recording and the speed of the device. The progress bar tracks the 20-second blocks as they are encoded, and the length and size of the result are shown before you start. Cancel stops the run at any point.

Does the M4A keep my sample rate and channels?

Yes, unless you change them. The WAV’s sample rate and its mono or stereo layout pass through to the encoder as they are. Choosing mono for a stereo recording halves the audio data before encoding, which suits speech. Tags and cover art in the WAV are not copied, and no dither or noise shaping is added.

Which bitrate is right for the M4A?

Higher bitrates keep more of the WAV and cost more space; lower bitrates give small files with more loss. A voice recording can go lower, while music deserves a higher setting. The size table below shows what each bitrate costs for several lengths, so you can decide before encoding.

How big will the M4A file be?

The M4A size follows the bitrate you choose. At 128 kbps a 3-minute song is 2.7 MB, at 256 kbps 5.5 MB and at 64 kbps 1.4 MB (1 MB = 1,048,576 bytes). The table also shows a WAV source for comparison.

LengthWAV 16-bitM4A 64 kbpsM4A 96 kbpsM4A 128 kbpsM4A 192 kbpsM4A 256 kbps
1 min10.1 MB0.5 MB0.7 MB0.9 MB1.4 MB1.8 MB
3 min30.3 MB1.4 MB2.1 MB2.7 MB4.1 MB5.5 MB
5 min50.5 MB2.3 MB3.4 MB4.6 MB6.9 MB9.2 MB
10 min101 MB4.6 MB6.9 MB9.2 MB13.7 MB18.3 MB

Frequently asked questions

How do I convert WAV to M4A?

Open the WAV here, pick a bitrate and press Save as M4A. When it finishes, press Download.

What is an M4A file?

M4A is an MPEG-4 audio file, usually holding AAC. Phones, iTunes and most players handle it.

What is a WAV file?

WAV is a file format that stores audio as uncompressed samples.

How do I open a WAV file?

Use any common media player or audio editor, or open it on this page.

How do I open an M4A file?

Apple devices and most players play M4A. This page opens it too.

Do you support other audio or video formats?

The page opens MP3, WAV, OGG, M4A, AAC, FLAC, AIFF and Opus audio. Video files are not supported.

Which browsers can create M4A?

Those with an AAC encoder; Chrome, Edge and Safari 26 or later have one. The page checks for it and shows a message when the encoder is missing.

Can I change the sample rate or make it mono?

Yes, in the Save panel. Sample rate and Channels both default to Same as source, so the M4A keeps the WAV’s values unless you change them. Mono suits speech, because it needs less data than stereo at the same bitrate setting.